MAGUS

LAT-1000A Series

Enables Highly Accurate Measurement Possible to Inference Correction by Arithmetic Processing.

Each system in the LAT-1000A series consists of the LAT-A 6-component force transducer and the FDP-106A signal processor. The LAT-A simultaneously detects 3 forces in 3 axial directions orthogonal to the transducer and 3 moments around the 3 axes. The FDP-106A automatically eliminates interference components contained in transducer output through calculation. By minimizing errors due to interference, the system enables highly accurate measurement of both single and multiple component force loads. (Patented)

Features

?? 5-V output available with the rated load
?? To guarantee measurement accuracy, performance
with multiple component force loaded is indicated with a maximum error (see note in the next page).
?? Highly accurate measurement possible even with multiple component force loaded
?? Simultaneous sampling of 6-component force and processing signals
up to approximately 300 Hz possible
?? The compact, lightweight transducer is strain gage based and is cased
with a highly rigid special aluminum alloy.
?? Calibration coefficient is preset in the signal processor, enabling immediate measurement
by connecting a monitor indicator.
?? Force and moment can be read directly on a PC if connected.
?? Direct reading mode is provided to read force and moment at the load point.
?? High/low limit and hysteresis width of the high/low limit are set to alarm output.

PDF Download

Configuration

?? 6-component force transducer LAT-A
?? Signal processor FDP-106A
?? PC (not included)

General Specifications

Rated Capacity

Model	Rated Capacity
Model	Fx N	Fy N	Fz N	Mx N･m	My N･m	Mz N･m
LAT-1030KA-1	300	300	300	10	10	10
LAT-1030KA-2	300	300	300	20	20	20

Safe Overload Rating	120%
Nonlinearity	Within??0.5% RO
Hysteresis	Within??0.5% RO
Interference	??0.8% RO
Maximum Error	??1.5% RO (??3% RO with LAT-KA-2)
Resolution	0.05% FS
Temperature Effect on Zero Balance	Within ??0.25% RO/??C
Temperature Effect on Output	Within ??0.05%/??C
Compensated Temperature Range	0 to 50 ??C

Specifications stated above are values measured with our calibrators under in company standard conditions.

6-Component Force Transducer LAT-A Specifications

Rated Capacity	Fx, Fy=300N, Fz=300N
	Mx, My, Mz=10, 20N･m
	See table in the previous page for combinations.
Safe Overload Rating	120%
Natural Frequency (with all models)	Fx??Fy : Approx. 2.3 kHz, Fz: Approx. 5.5 kHz
Natural Frequency (with all models)	Mx??My : Approx. 8 kHz, Mz: Approx. 4 kHz
Recommended Excitation Voltage	2.5V??DC
Safe Excitation Voltage	5V?? DC
Input Resistance	58.3?????10%
Output Resistance	350??? ??2%
Compensated Temperature Range	0 to 60??C
Safe Temperature Range	0 to 70??C
Temperature Effect on Zero Balance	Within 0.05% RO/??C
Temperature Effect on Output	Within 0.05%/??C
Weight	Each model approx. 250 g (not including cable)
Protection Rating	IP30 (JIS C 0920)
Cable	14-conductor (0.3 mm² ) PVC shielded cable, 9 mm diameter,with connector plug at both ends.
	N-78 for connection to FDP-106A (Shield wire is not connected to mainframe)
	For measurement of displacement and inclinaton angle, contact us .

Standard Accessories
Communications program (Windows version), torque wrench, hexagon socket wrench, parallel pins ??4 and ??8, connection cable N-78

�� Back to top